Specification-grade deck, stair, and cable railing systems · Partner since 2003

Cosentino Surface Inspection: The 8-Point Checklist I Use Before Anything Gets Installed


2026-11-13 · Gabriel Santos

Who this checklist is for

If you're the person who signs off on Cosentino deliveries—Dekton slabs, Silestone countertops, Sensa natural stone, custom shower pans, wall panels—this is the exact sequence I run. Eight steps. About 15 minutes per piece once you've done it a dozen times.

Quick context on me: I'm a quality and brand compliance manager at a surfacing fabrication shop. I review every piece before it goes out the door, roughly 300 items a month. In 2024 I rejected around 11% of first deliveries. Most of those were color drift and edge chipping, not the dramatic stuff people imagine. The checklist below is what took that rejection rate down from nearly 19% the year before.

It's not fancy. It just catches things before they cost you.

The 8 steps, in order

1. Confirm the batch number, not just the SKU

Everyone checks the product name. Almost nobody checks the batch against the packing list before they unbox.

I learned that the expensive way. We took delivery of what the paperwork called Dekton for a kitchen island. Two slabs turned out to be from a different production run. The shift was maybe Delta E of 3—small enough to look fine on its own, painfully obvious once the two halves were seamed. We'd already cut one.

Saved nothing. Ended up spending roughly $1,400 on replacement material plus two lost days on the schedule.

What to do: before anyone touches a saw, line up the batch numbers on the slab labels with the packing list. If two pieces that will sit in the same visible plane come from different batches, stop and call your rep. For Silestone especially, the veined and marbled finishes can shift noticeably between runs.

2. Check thickness and edge profile in at least three spots

Don't measure one corner and call it done. Measure near both ends and the middle. Slight variation is normal within spec; variation outside spec is what shows up as a visible lip at a seam three weeks later.

Dekton comes in a range of thicknesses—4, 8, 12, 20, and 30 mm—depending on the application. Verify against the printed spec sheet for that specific SKU, not against what the last shipment happened to be. I've seen a 12 mm spec get filled with an 8 mm panel because nobody looked past the color name.

Run your thumb along the finished edge, too. Feels dumb. Catches chips you'd otherwise find with your eyes at the client's house.

3. Do a light sweep for color and surface defects

Stand the slab upright and walk a portable light source across it at a low angle. This is the step most shops skip and it's the one that pays for itself fastest.

Low-angle light throws surface haze, pinholes, and polish inconsistencies into relief. You won't see them under overhead shop lighting—you'll see them under a pendant light in a client's kitchen at 7 p.m.

For natural stone like Sensa, this is also where you look for fissures and resin-filled areas. Those aren't necessarily defects—Sensa is a natural product and some character is expected—but you need to decide before fabrication whether they'll land in a visible spot or a cutout.

4. On shower pans, check slope and drain fit first

Custom-fabricated shower pans are where I see the most rework, mostly because the slope gets cut into the wrong plane or the drain collar sits a few millimeters off.

Local plumbing codes generally call for a quarter-inch of fall per foot toward the drain. Get a digital level and check it on the actual fabricated piece, not on the drawing. On a three-foot run, that's about three-quarters of an inch of drop—small enough that a tape measure won't save you.

Test-fit the drain assembly dry before you set anything. The tolerance between the cutout and the drain collar is tight, and a pan that has to be re-cut after sealing is a bad day for everyone.

5. Verify slip resistance on any shower floor

This one gets skipped because it's less intuitive than measuring a slab.

ANSI A326.3 sets a minimum dynamic coefficient of friction (DCOF) of 0.42 for level interior floors in wet conditions. That's the floor, not the wall. Barefoot shower floors are a high-risk wet area, so many specifiers push higher than the minimum—but 0.42 is the line you can't go under.

Ask your supplier for the DCOF rating of the specific finish, not the product family. Dekton and Silestone come in multiple surface textures and the numbers differ. A polished slab on a shower floor is the wrong call regardless of what the brochure says.

6. Dry-fit cutouts and seams before fabricating

Lay out the templates or the actual appliance cutouts on the slab. Check the position against the plan, not against the drawing your fabricator scribbled on a scrap of paper.

Where I've gotten burned: undermount sink cutouts shifting 6 mm because the template was taken from the old countertop instead of the new sink. Six millimeters is nothing until the sink doesn't center under the window.

Seam placement matters too. On large-format Dekton, seams should fall where they're least visible and away from high-impact areas. Decide this now. Once it's cut, it's decided.

7. Confirm adhesive and sealant compatibility

Cosentino materials are non-porous, which changes how adhesives and sealants behave compared to, say, granite. Use the manufacturer's specified adhesive system. This isn't a place to substitute what the installer has in the truck.

While you're on the subject, control what happens during clean-up. Strong adhesive removers and generic solvent-based cleaners can dull or stain the surface finish—especially on matte and textured Dekton. If a crew needs to remove adhesive residue, specify the cleaner and test it on an offcut first. A $15 bottle of the wrong remover can mean refinishing a $900 panel.

I keep a laminated card in the shop listing approved cleaners by material. It sounds overly formal. It's saved us twice.

8. Mock it up against the actual cabinetry, then close the paperwork

This is the step that separates a delivery that passes inspection from a delivery that passes the client's inspection.

Pull a sample or offcut into the room where it's going. White kitchen cabinets are unforgiving—they reflect color differently than a shop wall does, and a countertop that looked warm in the warehouse can read distinctly grey under white lacquer and north-facing light. Look at it in daylight and under the actual installed lighting before you commit to the order.

Then do the boring part the same day: photograph each piece with the batch label visible, register the warranty, and file the inspection record against the project number. Warranty registration gets forgotten constantly and it's the first thing that comes up when something fails 18 months later.

Mistakes I still see (including mine)

Inspecting under shop lighting only. Shop lights are designed to make everything look acceptable. Natural light and low-angle light tell the truth.

Trusting the paperwork over the piece. I've had deliveries where the packing list matched the order exactly and the slabs still came from different runs. The document is a claim. The slab is the fact.

Not writing down the rejection reason. If you reject something, note the measurement and the spec it failed against. Vendors argue with opinions and accept numbers.

Skipping the slope check on pans because "the fabricator does this every day." They do. That's exactly why a second set of eyes on the finished piece pays off—familiarity breeds shortcuts.

Looking back at our own numbers, the checklist didn't make us slower. It cut average inspection time from about 40 minutes per piece to under 15, because we stopped discovering problems at installation. That's the whole point. Catch it on the loading dock, not in someone's bathroom.

Share: WhatsApp
Gabriel Santos
Gabriel Santos

Gabriel Santos is a roofing and moisture-control analyst specializing in roof coverings, insulation boards, air and vapor control layers, waterproofing membranes, flashings, drainage components, and sealants. He uses ASTM C518 thermal-transmission and ASTM E96/E96M water-vapor data while tracking R-value, vapor permeance, membrane thickness, seam adhesion, drainage slope, wind-uplift evidence, and penetration detailing. His guidance helps enclosure consultants, roofers, and owners compare compatible assemblies for climate exposure, condensation control, leak risk, durability, and repair access.